Futaba FX-20 (V5) 2.4Ghz 14ch Transmitter & R6208SB HV Receiver S.Bus Combo w/ Battery
[F-FX20/R6208SB]

Model No.: F-FX20/R6208SB

Price: US$659.00

Availability: This product is currently SOLD OUT

Order quantity:

Available Options:
*Mode:

Futaba FX-20 (V3) 2.4Ghz 12+2ch Transmitter & R6108SB HV Receiver S.Bus Combo w/ Battery & Radio Tray

Updated with 14-Channel Digital Proportional R/C System & new R6208SB S.Bus receiver

2011-04: Firmware upgrade to V5.0 now.

Fully mounted computer console transmitter with integrated FASST 2.4 GHz technology with R6208SB RX

The Futaba FX-20 is now equipped with the latest software update ver 3.0, supports up to 14-Channel! It is a Computer Console Radio built with 2.4 GHz FASST technology designed for RC airplnes, helicopters and gliders. For the modelers with a love for the European style of RC sophistication.

Feature Highlights:

Sensor touch programming
LCD illuminated graphic display - high-resolution 128 x 64 dot
Universal mode for joystick coupling mechanism which has twin ball bearings. User-convertable for easy mode change
10 channels available (8 prop and 2 control channels)
Rotary trimming - Combination of analogue and digital trimming
2x Linear sliders for use with functions like gyros, flaps or governors
Equipped with 2 analogue rotary controls and 6 switches
Firmware update via SD card
20 internal model memories plus more on SD card

With the FX-20 system the range of robbe Futaba console transmitters is extended downwards, so permitting a low-cost entry point to 2.4 GHz technology.

The FASST system is a Spread Spectrum System with Frequency Hopping (FHSS). Therefore it may transmit a maximum power of 100 mW EIRP and so has sufficient reserves for even large-scale model aircraft and jets.
No shared channel disruption, almost impossible to have interference, not sensitive to electrical smog.
The central point is the high-resolution 128 x 64 dot graphical display which is backlit to ensure it is easy to read.
The system´s elegant design with clean lines is made possible by the new Cap Touch system. Contact-free sensors for the 3D hotkey allow a smooth and sealed surface without any protruding controls.
Simple programming in combination with the graphical user interface. The proven menu structure and user interface was mainly adopted from the FX30 system, as was the modern and practical design of the casing.
The software is available in 8 languages: German, English, French, Italian, Spanish, Czech, Russian or Dutch.
The joystick coupling mechanism has twin ball bearings and is designed for Universal mode. They can easily be converted by the user themselves from "throttle right" to "throttle left". The FX-20 transmitter features the new rotary stick trimming. This type of trimming combines the advantages of traditional analogue trims with those of digital trimming. With just one movement, the direction and size of the trim will be set and automatically stored.
The linear sliders are very practical in use for additional functions such as gyros, flaps or governors.
In total the system has 10 channels available (8 prop- and 2 control channels), while the channel sequence can be defined however you want.
The transmitter is supplied fully equipped with 2 analogue rotary controls and 6 switches.
As with all robbe console transmitters this system also allows for stick switches to be built in. The electrical connectiobn is already present internally..
All the different types of control are available. The sequence of the controls can be chosen freely, as well as the sequence of the servo outlets.
Comprehensive Software has all the necessary functions for power, glider and helicopter models. Plenty of freely programmable mixers, optionally with 5-point curve,for setting up very complex mixer functions..
Integrated trainer system with individual function switching. Freely configurable trainer channel assignment..
Using the SD-card the system software can be updated by the user themselves to the latest version at any time.
20 internal model memories, with infinite expansion using SD-card - 3862 models per 2 GB.

General functions

4 joystick functions, 6 switches, 2 knob controls, 2 linear sliders, optionally 2 stick switches.
2 operating hours counters, of which one relates to a stored model
2 freely settable stopwatches, with memory function
Selectable large-scale display of stopwatches
Key-lock function
Selection of model, 20 internal model memories, extensible to 3862 models using optional SD-card (2 GB)
Stored model can be selected directly from the startup display
Trim value display in steps or %, with zeroising per trim memory

System functions

Trainer Mode with individual function switching and mixed operation
Trainer function also on virtual channels, 8 or 12 channel operation
Freely configurable trainer channel assignment
Hardware-reversal for all controls and switches
Stick mode settings 1-4
User name of 10 characters
Choice of language: German,, English, French, Italian, Spanish, Czech, Russian or Dutch.

Functions Basic

Graphical servo monitor with neutral- and servo- test
Choice of model and copy function, model name of 10 characters
Model type selection, power model, glider, helicopter
Frequency switching General/France and modulation switching 7/12 channel.
Freely adjustable emission sequence for channels 1-8
Free choice of control types and trimmer options for all functions
Free choice of control type and trimmer options also for virtual channels.
For all control types (including switces etc.) free choice of trimmer options
Digital joystick trimming, optionally with normal- or ATL (asymmetric) trim function. Optionally in "global" mode (effective in all flight modes) or in "single" mode, (effective only in the relevant flight mode).
Free assignment of control types for control channels 9 + 10.
Servo centre point setting for channels 1-8
Servo reversal for channels 1-10
Failsafe setting, channel 3 (gas) in 7-channel mode, for all channels in multi-mode.
Servo travel adjustment with limit function (ATV) for the 8 prop-channels
End point setting with limit function for channels 1-8
Switch off Motor function
Trim step setting
Idling 2, new with +/- rate
Selectable mixer alarm

Functions for power models
a wide range of mixer menus for models with up to 4 wing-mounted servos. In addition to the choice of wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Deltas and powered flying wings with 2 ... 4 wing-mounted servos are also available. These mixer menus are pre-programmed to suit the model type, and contain all the essential mixer functions as standard.

5 freely assignable and switchable dual rate /expo settings.
5 free programmatic linear or 5 point curve per stored model, optionally with / without trimming and offset add-in.
5-point gas curve
Speed settings for gas servo
Rudder diferentiation
Mixer spoiler (Flaperon)
Mixer elevator- spoiler (Flaperon)
Mixer rudder-aileron
Mixer rudder-elevator
Mixer Snap Roll
Mixed adjustment
Gyro setting
Mixer motor, for 2-step switching of motors, with separate speed settings for steps 1 /2 as well as forwards and backwards.

Glider functions
Also for model gliders there are many mixer menus available for models with up to 6 wing-mounted servos. Optionally with or without motor. In addition to the choice of wing type, the user can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Flying wings with 2...6 wing-mounted servos can also be selected. These mixer menus are pre-programmed to suit the model type, and contain all the essential mixer functions as standard.

5 flight conditions per model memory, with priority allocation and adjustable switching delays. With logical switch function.
5 free programmatic linear or 5 point curve per stored model, optionally with / without trimming and offset add-in.
Rudder differentiation
Travel adjustment plain flaps
Mixer aileron-plain flaps
Mixer aileron-rudder
Mixer spoiler-plain flaps
Mixer elevator-spoiler
Mixer plain flap-elevator
Mixer rudder-aileron
Mixer Butterfly with offset and delay settings
Mixer Butterfly - elevator
Mixer trim-mix for aileron, rudder, and elevator, with speed setting and and FZS-switch delay.
Gyro settings
Mixer motor, for 2-step switching of motors, with individual speed settings for steps 1 /2 as well as forwards and backwards.
5-point curve for motor function

Helicopter functions
The mixer menus for helicopters are mainly different by use of swash plate controls. All the classic linkage types are included as standard: H1, H2, HR3, HN3, H4 and the new H3 90° and H3 140°
A special feature is the new form of variable pushrod travel compensation for the H3 and H4 types. This function eliminates a common problem found with unequal travels, which can result in servo damage can occur in the long term, when travels are fairly large or asymmetrical. The speed of the pitch-axis (elevator) function can also be adjusted, in order to avoid the run-time differences with the HR3 / HN3 120° swashplate linkage.

5 free programmmatic linear or 5 point curves per stored model, optionally with / without trimming and offset add-in.
Swash plate ring mixer
5-point-pitch curve normal, gas pre-selection 1,2,3, auto-rotation. With logic switch function. .
5-point-gas curve normal, gas preselection 1,2,3, auto-rotation. With logic switch function.
Auto-rotation
Swash plate mixer (virtual rotation)
Swash plate mixer – Gas (Linear / Centre)
Tail mixer – Gas (Linear / Center)
5-Point mixer tail pitch, normal, gas presetting 1,2,3, auto-rotation. With logical switch function.
Mixed adjustments
Gyro mixer with 3 steps and fine trim setting
Governor with 3 steps and fine trim setting
Gas Limiter

Included in this package:

Futaba FX-20 radio
Futaba R6208SB S.Bus 2.4GHz 8 channel receiver
Radio Tray
Futaba 7.2V 1700mAh NiMH transmitter battery
Battery Charger
Control Sticks
Radio Neck Strap
Switch Harness
CD Instruction Manual

Current Reviews: 2

This product was added to our catalog on Saturday, 03. December 2011.

Futaba FX-20 (V5) 2.4Ghz 14ch Transmitter & R6208SB HV Receiver S.Bus Combo w/ Battery[F-FX20/R6208SB]

Price: US$659.00

Futaba FX-20 (V3) 2.4Ghz 12+2ch Transmitter & R6108SB HV Receiver S.Bus Combo w/ Battery & Radio Tray

Futaba FX-20 (V5) 2.4Ghz 14ch Transmitter & R6208SB HV Receiver S.Bus Combo w/ Battery
[F-FX20/R6208SB]