Futaba 14SG 2.4Ghz FASSTest/FASST/FHSS 14ch Transmitter & R2008SB HV Receiver S.Bus Combo
[F-14SG/R2008SB/FHSS]

Futaba 14SG 2.4Ghz FASSTest/FASST/S-FHSS 14ch Transmitter & R2008SB HV Receiver S.Bus Value Combo

Using the normal S.Bus system. Good to use wih DJI NAZA / WooKong / Phantom controllers!

FASSTest tech. Flybarless gyro support. S.Bus2 programmability. Telemetry.

The 14SG has it all. . . and more!

The software menu is available in many languages: English, Italian, Deutsch, French, Italiano, Espanol, Dutch, Russian, Japanese and čeština.

Futaba proudly introduces the 14SG, the only 14-channel system with revolutionary 2.4GHz FASSTest technology. It's also compatible with Futaba FASST and S-FHSS protocols, so you can fly with virtually any 2.4GHz air receiver Futaba produces.

The 14SG can transmit and receive telemetry data. Install Futaba telemetry sensors (sold separately) to monitor flight data, receive alerts while in flight and more. Heli pilots will prefer the 14SG's 3-axis gyro support — which makes the 14SG the perfect system for flybarless flight!

The innovations don't stop there. Turn the 14SG over, and you'll see the construction is as rock-solid as any other Futaba system. It's also very comfortable to use, thanks to rubber grips that help minimize flyer fatigue — an added bonus that pilots will appreciate.

The 14SG has so much to offer, we can't talk about everything here. To see everything that the 14SG can do, read on. . .

About the 14SG: Channels: 12 proportional, 2 switched Compatible with FASSTest, FASST and S-FHSS protocols FASSTest telemetry – compatible with Futaba telemetry sensors (sold separately) Free user-updatable software 30-model memory 10-character user naming 10-character model naming Airplane, helicopter and glider programming Large, 1.75” x 3” backlit LCD screen with 128 x 64 resolution SensorTouch™ programming SD Card compatibility for external model memory and software updates (SD: 32MB-2GB; SDHC 4GB-32GB) Left and right assignable slider switches Two assignable rotary knobs Six assignable three-position switches One assignable momentary two-position switch One assignable two-position switch Comfortable rubber grips on the sides and back Wide top switch spacing Adjustable stick tension Dual ball bearing gimbals 4 vibration warning types Home/Exit; User Menu/Servo Monitor buttons Audio earphone jack (for telemetry alarms) 6V 1800mAh NiMH battery pack User stick calibration Trainer system Servo speed adjust 5 programmable mixes V-tail, Ailvator, winglet, motor mixing Trim mix Logic switch (condition switch only) Internal programmer for S.Bus servos User menu Servo monitor (neutral and moving tests) 2 count up/countdown timers Integral timer Model timer Quick model select

Airplane Features 7 different wing types 3 different tail types 2 different rudder types Flap setting menu Differential ailerons Aileron to camber flap mixing Aileron to brake flap mixing Aileron to rudder mixing Rudder to aileron mixing Rudder to elevator mixing Camber mixing Elevator to camber mixing Camber flap to elevator mixing Snap roll mixing Airbrake mixing V-Tail mixing Ailvator Winglet Motor mixing Fuel mixture mixing (single and twin) Gyro mixing Throttle curve (5-point) Pitch curve (5-point) Idle down

Helicopter Features 6 swash plate types Pitch/throttle curves (5-point) Throttle hold Swash mix Throttle mix Pitch to rudder mixing Fuel mixture Gyro (Flybarless support) Governor (700-3500 rpm) Hover pitch Hover throttle High/low pitch Swash AFR Swash setting (mixing rate, linkage compensation, speed compensation) Swash ring (electronic) Throttle cut Glider Features 11 different wing types 3 different tail types 2 different rudder types Flap setting menu Differential ailerons Aileron to camber flap mixing Aileron to brake flap mixing Aileron to rudder mixing Rudder to aileron mixing Rudder to elevator mixing Camber mixing Elevator to camber mixing Camber flap to elevator mixing Butterfly mixing Butterfly to elevator mixing

Programming port & earphone jack

Rubber hand grips and adjustable gimbals

Wide switch spacing

Edit switches

Battery compartment/SD card slot

Balances perfectly

Home screen

Main telemetry screen

Servo speed screen

Modulation screen

User-configurable menu

Customizable quick select menu

Sensor warning setup menu

3-axis gyro menu

Governor menu

Package Included:
- Futaba 14SG transmitter
- Futaba R2008SB FHSS receiver
- Futaba HT5F1800B 6.0V 1800mAh NiMH Tx battery
- Futaba HBC-3C(4) Battery Charger (220V only, different than the charger of 10C and 8FG)
- Swith harness
- Neck strap
- LiFe Battery Spacer
- English Manual
 

Note:
This Futaba 14SG is configured to S-FHSS 2.4Ghz transmission mode to connect with the R2008SB receiver.
This product is CE certified.  NO SERVO is bundled with this combo.
This product must be shipped with INSURED AirParcel or EMS (Free upgrade to DHL for most EU regions), please select EMS when you checkout if you are not sure whether your region supports insured airparcel or not. You may also contact us to confirm before you place the order. Safe packing weight: 3KG, you may ship it together with other products.
14SGA and 14SGH are interchangeable, we only stock helicopter model at the moment, but it can be easily changed to airplane model.
Our 2.4Ghz Futaba transmitters & receivers are globally compatible. That means they can be linked with any 2.4Ghz Futaba transmitter or receiver sold in other regions. (e.g. our transmitter with US receiver)
Our Futaba products are directly manufactured by the original Futaba Corporation, Japan (双葉電子工業株式会社). RC711 is not the affiliate of Hobbico, Inc in the United States.
Subject to availability, we will refund you the total amount if we cannot ship out this product to you in 7 days.
Our Futaba 14SG transmitter contains the software option to switch to the "France" mode which compliance with the French radio regulations:
LINKAGE MENU -> SYSTEM -> G (General) changes to F (France).